The Beholder EC1 is designed specifically for professional filmmakers looking for a single handheld stabilizer for a large range of medium and small cameras weighing up to 4.5 lbs. The Beholder EC1 is lightweight, easy to use, and can be carried in the supplied case or a small photographer bag.
The 3-Axis gimbal features three 360 degree rotating brushless motors that give you a limitless range of motion.
With a payload of up to 4.5 lbs., the EC1 has the ability to stabilize a wide range of today's popular DSLR and mirrorless cameras. Sony a6500, Sony a7SII, Panasonic GH5, and the Canon 5D Mark IV are just a few cameras that the EC1 can handle.
Using a 32-bit controller with a 12-bit encoder, the EC1 uses an adaptive PID algorithm to produce a reliably efficient handheld stabilizer.
In Lock Mode, the Yaw, Pitch, and Roll axis work together to keep the camera pointed in one direction. The camera's composition will stay the same no matter how you move the handle.
Quickly lock your camera into any position by manually pointing and holding it in any direction. After a few seconds, the camera will lock and hold its position until it is reset back to default.
Switch to Inverted Mode at any time by simply flipping the handle over the camera. Inverted Mode can be operated in conjunction with any of the Lock and Follow Modes.
The EC1 features 3 different follow modes. In Yaw-Axis Follow Mode, the EC1 will only follow your Pan movements. In Pitch and Yaw-Axis Follow mode, the EC1 will follow your Pan and Tilt Movements. Finally, the 3-Axis Follow Mode gives you full control allowing you to Pan, Tilt, and Roll.
Lock Mode will allow the camera to hold a certain direction, and will not follow, pan, or tilt.
Pan-Follow Mode allows the gimbal to follow pan axis, and hold the tilt position.
Follow Mode allows the camera to follow both tilt and pan directions.
3-Axis Follow Mode has no restrictions as it allows the camera to follow pan, tilt, and roll.
A display screen located on the back of the handle conveniently provides you with information on the battery life and operating mode.
With a newly designed quick-release baseplate system, the EC1 is easy to balance without the need of any tools.
The EC1 handle comes with two 1/4-20 mounts that are perfect for mounting accessories such as a light, microphone, or monitor. A 3/8-16 thread located on the bottom allows you to securely mount the EC1 to a tripod, jib, or dual handle support system such as the Ikan DGH.
Beholder EC1 3 Axis Gimbal Balancing Tutorial
Watch Julio Ramon from Ikan Corp balance the new Beholder EC1 3-axis handheld gimbal stabilizer for DSLR and Mirrorless cameras.
2.0 - 4.5 lbs
907 - 1040g
Small Zoom Lens
Small, lightweight lenses are recommended.
Long or heavy lenses may be difficult to balance.
|Battery Charge Time: 3 - 4 Hours|
|Battery Operating Time: 8-10 Hours|
|Battery Stand By Time: Up to 20 Hours|
|Battery Type: 18650, 3.7V, 2600mAh, Li-Ion Batteries|
|Camera Compatibility: Most Mirrorless and DSLR Cameras|
|Shipping Dimensions: 15.75 x 8.5 x 3.75 in.|
|Shipping Dimensions (Metric): 400 x 215 x 95 mm|
|Shipping Weight: 6 lbs|
|Shipping Weight (Metric): 2.7 kg|
|UPC Code: 847983019465|
|Weight : 2.6 lbs|
|Weight (Metric): 1.17 kg|
|Working Angle (Pan Motor): 360°|
|Working Angle (Roll Motor): 360°|
|Working Angle (Tilt Motor): 360°|